MazicBay Diagnostics
MAZICBAYDiagnostics
FTC Reader Disclosure: When you purchase or register through links on our site, we may earn an affiliate commission at no extra cost to you. Read our Editorial & Advertising Policy.

P0139 on GMC: Symptoms, Causes & Fix

O2 Sensor Circuit Slow Response (Bank 1 Sensor 2)

Official technical diagnostic wire for fault code P0139 specifically affecting GMC vehicles (Sierra 1500, Yukon, Acadia, Canyon, Terrain).

Sensor Voltage Ref
0.1V – 5.0V Ref
GMC Factory Standard
CAN Bus Speed
500 kbps CAN-FD
ISO 15765-4 Diagnostic Bus
Drivability Status
Drivable (Short Trip)
Low urgency level
Est. Repair Cost
$100 - $300 (DIY: $35 - $100)
Parts & Labor DIY
Model-Specific Diagnostic Wires

Select Your GMC Model for P0139:

5 Models Available

1. Common Symptoms on GMC Vehicles

When GMC Engine Control Modules (ECM) trigger fault code P0139, drivers typically report:

Check Engine Light on on GMC Powertrains
Slow switching response on scan tool graphs on GMC Powertrains
Failed emissions readiness monitors on GMC Powertrains

2. Root Causes on GMC Engines

Historical diagnostic claims across GMC engines point to the following failure distribution:

55%
Aged and degraded downstream O2 sensor coated in carbon / silicon deposits (GMC OEM Part)
25%
Exhaust leak near downstream sensor (GMC OEM Part)
12%
Degraded internal heater in oxygen sensor (GMC OEM Part)
8%
High electrical resistance in wiring harness (GMC OEM Part)

3. Step-by-Step Fix Protocol for GMC

01
Verify Sensor Slow Response on Graph

Use scanner graphing mode. Perform rapid deceleration fuel cutoff. Sensor should drop quickly to 0.1V. If response lags by several seconds, sensor is worn. on GMC engines.

Required Tool: Graphing OBD-II Scanner
02
Replace Downstream O2 Sensor

Install new OEM downstream oxygen sensor to restore fast switching response. on GMC engines.

Required Tool: 22mm O2 Sensor Socket, Ratchet
03
Clear Trouble Codes

Clear DTCs and drive at 55 mph for 10 miles to set readiness monitors. on GMC engines.

Required Tool: OBD-II Scanner
Recommended Parts & Testing Tools

Equipment for Diagnosing GMC (P0139)

Prime Fast Delivery & Verified Fitment
Direct-Fit Replacement Part

GMC OEM Replacement Sensor

4.7 / 5.0 (Verified Fit)

Direct-fit replacement assembly engineered to OEM tolerances for GMC.

$45 – $95 Prime
Check Fitment on Amazon
Sensor Signal Voltage Meter

AstroAI Auto-Ranging Digital Multimeter

4.6 / 5.0 (Best Seller)

Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.

$29.99 Prime
View on Amazon
Top Mobile OBD-II Scanner

BlueDriver Bluetooth Pro OBDII Scan Tool

4.7 / 5.0 (50,000+ Reviews)

Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.

Compare OEM & Aftermarket Replacement Sensors for GMCVerified direct-fit pricing from Denso, Bosch, Motorcraft, and ACDelco on Amazon.
Find Parts on Amazon
* As an Amazon Associate, MazicBay earns from qualifying purchases. Prices & availability subject to change.

4. GMC P0139 Frequently Asked Questions

What does code P0139 mean on a GMC?

On GMC vehicles, P0139 indicates that the Engine Control Module (ECM) detected o2 sensor circuit slow response (bank 1 sensor 2). This typically points to Aged and degraded downstream O2 sensor coated in carbon / silicon deposits or Exhaust leak near downstream sensor.

Can I continue driving my GMC with code P0139?

Yes. Safe to drive normally, but will fail emissions inspection. Because this code carries a Low severity rating on GMC powertrains, we recommend scanning live data values promptly to prevent secondary damage.

How much does it cost to fix code P0139 on a GMC?

Estimated DIY parts cost ranges from $100 - $300 (DIY: $35 - $100), while professional shop repairs at an authorized GMC dealership or independent specialist typically range from $180 to $380 including diagnostic labor.