P0112 on Audi A6
Factory diagnostic protocol and troubleshooting wire for fault code P0112 specifically for the Audi A6 (2020–2026, 3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro).
1. Symptoms of P0112 on Audi A6
When the Engine Control Module (ECM/PCM) on your Audi A6 (3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro) logs fault code P0112, drivers commonly observe:
2. Most Likely Causes on Audi A6
Historical warranty claims and technical repair bulletins for Audi A6 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Audi A6
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0112 to note engine RPM, load, and voltage when the fault triggered. on the Audi A6 equipped with 3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro.
Inspect the electrical connector and wiring harness related to P0112 for chafing, corrosion, moisture, or pin push-out. on the Audi A6 equipped with 3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro.
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Audi A6 equipped with 3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro.
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Audi A6 equipped with 3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro.
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Audi A6 equipped with 3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro.
Equipment for Diagnosing Audi A6 (P0112)
VVT Oil Control Solenoid Valve
Restores accurate camshaft timing and oil pressure regulation on Audi A6.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Audi A6
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Audi A6:
4. Audi A6 P0112 FAQs
What causes code P0112 to trigger on a Audi A6?
On the Audi A6 (3.0L Turbo V6 (A7/A8 S6 450HP) / 2.0L TFSI 261HP / 55 TFSI quattro), P0112 is most frequently caused by IAT sensor shorted to ground or Damaged wiring harness.
Where is the OBD-II port located on my Audi A6?
On the Audi A6, the 16-pin DLC diagnostic connector is located Driver lower dash trim near parking brake assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Audi A6 with code P0112?
Yes. ECM assumes intake air is 280°F+. Given that P0112 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.