B0091 on Chevrolet Colorado
Factory diagnostic protocol and troubleshooting wire for fault code B0091 specifically for the Chevrolet Colorado (2021–2026, 2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road).
1. Symptoms of B0091 on Chevrolet Colorado
When the Engine Control Module (ECM/PCM) on your Chevrolet Colorado (2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road) logs fault code B0091, drivers commonly observe:
2. Most Likely Causes on Chevrolet Colorado
Historical warranty claims and technical repair bulletins for Chevrolet Colorado point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chevrolet Colorado
Disconnect battery negative cable and wait 15 minutes to fully discharge SRS backup capacitors before touching airbag components. on the Chevrolet Colorado equipped with 2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road.
Remove driver side door sill trim / lower B-pillar trim to access the yellow impact sensor. on the Chevrolet Colorado equipped with 2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road.
Inspect sensor for water corrosion or cracked plastic housing. on the Chevrolet Colorado equipped with 2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road.
Bolt new OEM side impact sensor into clean, rust-free ground location, torque bolt to spec, and click yellow locking connector firmly. on the Chevrolet Colorado equipped with 2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road.
Reconnect battery, clear SRS trouble codes with an airbag-capable scanner, and verify light turns off after 5-second bulb check. on the Chevrolet Colorado equipped with 2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road.
Equipment for Diagnosing Chevrolet Colorado (B0091)
Chevrolet Colorado OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chevrolet Colorado.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chevrolet Colorado
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chevrolet Colorado:
4. Chevrolet Colorado B0091 FAQs
What causes code B0091 to trigger on a Chevrolet Colorado?
On the Chevrolet Colorado (2.7L Turbo 4-Cyl (310HP) / 3.6L V6 (308HP) / ZR2 AEV / Bison Off-Road), B0091 is most frequently caused by Corroded or damaged left side impact crash sensor (B-pillar or door sill) or Corroded wiring harness under driver seat / driver door sill.
Where is the OBD-II port located on my Chevrolet Colorado?
On the Chevrolet Colorado, the 16-pin DLC diagnostic connector is located Under driver side dashboard, left of center stack. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chevrolet Colorado with code B0091?
Caution. Side curtain and seat airbag deployment may be disabled in a side-impact collision. Given that B0091 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.