P2097 on Chrysler 300
Factory diagnostic protocol and troubleshooting wire for fault code P2097 specifically for the Chrysler 300 (2020–2025, 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)).
1. Symptoms of P2097 on Chrysler 300
When the Engine Control Module (ECM/PCM) on your Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)) logs fault code P2097, drivers commonly observe:
2. Most Likely Causes on Chrysler 300
Historical warranty claims and technical repair bulletins for Chrysler 300 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler 300
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P2097 to note engine RPM, load, and voltage when the fault triggered. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Inspect the electrical connector and wiring harness related to P2097 for chafing, corrosion, moisture, or pin push-out. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Equipment for Diagnosing Chrysler 300 (P2097)
Chrysler 300 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chrysler 300.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler 300
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler 300:
4. Chrysler 300 P2097 FAQs
What causes code P2097 to trigger on a Chrysler 300?
On the Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)), P2097 is most frequently caused by Leaking fuel injector or High fuel pressure.
Where is the OBD-II port located on my Chrysler 300?
On the Chrysler 300, the 16-pin DLC diagnostic connector is located Under driver side dash near left knee panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler 300 with code P2097?
Yes. Downstream O2 sensor indicates rich catalyst output. Given that P2097 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.