P0300 on Chrysler Pacifica Hybrid: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0300 (P0300: Random or Multiple Cylinder Misfire Detected) specifically on the Chrysler Pacifica Hybrid (2020–2026, 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)).
1. Symptoms of P0300 on Chrysler Pacifica Hybrid
When the Engine Control Module (ECM/PCM) on your Chrysler Pacifica Hybrid (3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)) logs fault code P0300, drivers commonly observe:
2. Most Likely Causes on Chrysler Pacifica Hybrid
Historical warranty claims and technical repair bulletins for Chrysler Pacifica Hybrid point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler Pacifica Hybrid
Plug a handheld OBD-II scanner into the 16-pin port under the dashboard. Check if specific cylinder codes like P0301 (Cylinder 1) or P0304 (Cylinder 4) accompany P0300. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Remove the ignition coils, use a spark plug socket with ratchet to unthread spark plugs. Inspect electrode tips for carbon buildup, oil fouling, or burnt gaps. Replace with OEM iridium plugs gapped to spec. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Perform an ignition swap test: Swap coil from a suspected misfiring cylinder to an adjacent cylinder. Clear codes and re-scan. If the misfire moves, replace the faulty coil. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Inspect PCV hoses, intake boot, and vacuum lines for cracking or hissing sounds while engine idles. Smoke test the intake if necessary. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Add a bottle of premium fuel injector cleaner (e.g. Chevron Techron). Clear the OBD-II codes with your scanner and take the car on a 15-minute drive cycle to confirm readiness monitors reset. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Other Common Fault Codes on Chrysler Pacifica Hybrid
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler Pacifica Hybrid:
4. Chrysler Pacifica Hybrid P0300 FAQs
What causes code P0300 to trigger on a Chrysler Pacifica Hybrid?
On the Chrysler Pacifica Hybrid (3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)), P0300 is most frequently caused by Worn or fouled spark plugs and damaged spark plug wires or Failing ignition coils or coil packs.
Where is the OBD-II port located on my Chrysler Pacifica Hybrid?
On the Chrysler Pacifica Hybrid, the 16-pin DLC diagnostic connector is located Under driver side dashboard above foot pedal assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler Pacifica Hybrid with code P0300?
No. Driving with a flashing check engine light causes irreversible catalytic converter damage. Given that P0300 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.