P0230 on Dodge Challenger
Factory diagnostic protocol and troubleshooting wire for fault code P0230 specifically for the Dodge Challenger (2020–2026, 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)).
1. Symptoms of P0230 on Dodge Challenger
When the Engine Control Module (ECM/PCM) on your Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)) logs fault code P0230, drivers commonly observe:
2. Most Likely Causes on Dodge Challenger
Historical warranty claims and technical repair bulletins for Dodge Challenger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Challenger
Inspect the Fuel Pump fuse in under-hood fuse box. Swap the fuel pump relay with an identical non-critical relay (like the horn relay). on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Have an assistant turn key to ON while listening at the open fuel filler neck. A healthy pump hums for 2–3 seconds. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Check for 12V battery power on pin 30 and 86, and check for PCM ground command on pin 85 when key is turned on. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
On vehicles with an electronic FPDM (such as Ford F-150s mounted on rear axle), check for corrosion or cracked aluminum housing. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
If power and ground reach the pump connector but pump does not spin, drop tank or access fuel pump hatch to replace pump assembly. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Equipment for Diagnosing Dodge Challenger (P0230)
Dodge Challenger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Challenger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Challenger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Challenger:
4. Dodge Challenger P0230 FAQs
What causes code P0230 to trigger on a Dodge Challenger?
On the Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)), P0230 is most frequently caused by Blown fuel pump fuse or burnt fuel pump relay or Open or shorted control circuit wiring between PCM and fuel pump relay.
Where is the OBD-II port located on my Dodge Challenger?
On the Dodge Challenger, the 16-pin DLC diagnostic connector is located Under driver dash left of center stack. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Challenger with code P0230?
No. The engine will crank but not start or will suddenly stall while driving when the fuel pump cuts out. Given that P0230 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.