P0705 on Dodge Challenger
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the Dodge Challenger (2020–2026, 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)).
1. Symptoms of P0705 on Dodge Challenger
When the Engine Control Module (ECM/PCM) on your Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on Dodge Challenger
Historical warranty claims and technical repair bulletins for Dodge Challenger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Challenger
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Equipment for Diagnosing Dodge Challenger (P0705)
Dodge Challenger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Challenger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Challenger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Challenger:
4. Dodge Challenger P0705 FAQs
What causes code P0705 to trigger on a Dodge Challenger?
On the Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my Dodge Challenger?
On the Dodge Challenger, the 16-pin DLC diagnostic connector is located Under driver dash left of center stack. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Challenger with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.