P0443 on Dodge Durango
Factory diagnostic protocol and troubleshooting wire for fault code P0443 specifically for the Dodge Durango (2021–2026, 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP)).
1. Symptoms of P0443 on Dodge Durango
When the Engine Control Module (ECM/PCM) on your Dodge Durango (3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP)) logs fault code P0443, drivers commonly observe:
2. Most Likely Causes on Dodge Durango
Historical warranty claims and technical repair bulletins for Dodge Durango point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Durango
Find the purge valve mounted on the intake manifold with one vacuum line leading to the intake and one to the charcoal canister. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Unplug 2-pin connector and measure resistance across terminals with multimeter. Typical spec is 14–30 ohms. If open (OL) or shorted (0 ohms), solenoid is dead. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Remove purge valve and blow into it. A healthy de-energized purge valve should be 100% sealed. If air passes through, the internal seal is stuck open. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Disconnect quick-release vapor lines, unbolt mounting bracket, snap new OEM purge valve into place, and reconnect electrical plug. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Clear DTCs with scanner and verify EVAP monitor completes. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Equipment for Diagnosing Dodge Durango (P0443)
OEM Tethered Fuel Gas Cap with O-Ring
Tight-sealing factory fuel cap resolves common EVAP small/large leak codes without workshop visits.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Durango
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Durango:
4. Dodge Durango P0443 FAQs
What causes code P0443 to trigger on a Dodge Durango?
On the Dodge Durango (3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP)), P0443 is most frequently caused by Failed EVAP purge solenoid coil (open or shorted internally) or Broken or frayed wiring harness to purge valve connector.
Where is the OBD-II port located on my Dodge Durango?
On the Dodge Durango, the 16-pin DLC diagnostic connector is located Driver lower dash panel near fuse box. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Durango with code P0443?
Yes. Safe to drive, but engine may experience hard starting after refueling at gas station. Given that P0443 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.