FTC Reader Disclosure: When you purchase or register through links on our site, we may earn an affiliate commission at no extra cost to you. Read our Editorial & Advertising Policy.

P0171

Ford Bronco GuideMedium Severity

P0171 on Ford Bronco: Symptoms, Causes & DIY Fix

Official technical diagnostic wire for fault code P0171 (P0171: System Too Lean (Bank 1)) specifically affecting Ford Bronco vehicles equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).

DIY Parts Estimate

$80 - $350 (DIY: $15 - $70)

Bronco Direct Fit

Shop Labor Quote

$180 – $380

Based on $120/hr labor

Drivability Status

Drivable (Short Trip)

Medium urgency level

Est. DIY Time

45 – 90 Min

Basic hand tools

Check P0171 On Another Ford Model:

Ford F-150 Ford F-250 Super Duty Ford Explorer Ford Mustang Ford Bronco Ford Ranger Ford Maverick

1. Symptoms of P0171 on Ford Bronco

When the Engine Control Module (ECM/PCM) on your Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)) logs fault code P0171, drivers commonly observe:

Check Engine Light on on Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP))

Rough idling or engine hesitation on acceleration on Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP))

Hard starting in cold weather on Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP))

Pinging or knocking sound under load on Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP))

Ford Bronco OBD-II Port Location

The 16-pin diagnostic connector is located Beneath steering wheel lower shroud. Plug in your scan tool to verify freeze-frame sensor values.

2. Most Likely Causes on Ford Bronco

Historical warranty claims and technical repair bulletins for Ford Bronco point to the following failure distribution:

55%

Dirty or failing Mass Air Flow (MAF) sensor (Ford OEM Part)

25%

Cracked intake air boot or disconnected vacuum hose (Ford OEM Part)

12%

Clogged fuel filter or weak fuel pump (Ford OEM Part)

Stuck open PCV valve or leaking intake manifold gasket (Ford OEM Part)

3. Step-by-Step DIY Repair Guide for Ford Bronco

Clean the Mass Airflow (MAF) Sensor

Disconnect the battery, unclip the MAF sensor on the air intake tube, and spray 10-15 bursts of dedicated MAF cleaner onto the thin wire sensor. Allow to dry 15 minutes before reinstalling. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).

Required Tool: CRC MAF Sensor Cleaner, Screwdriver

Inspect Intake Air Ducting

Check the rubber accordion hose between air filter box and throttle body for tears or dry rot cracks. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).

Required Tool: Flashlight

Inspect PCV Valve and Hoses

Shake the PCV valve; if it doesn't rattle cleanly, replace it. Inspect attached rubber hoses for collapsing. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).

Required Tool: Pliers

Check Fuel Pressure

Connect fuel pressure gauge to the Schrader valve on fuel rail. Verify pressure meets factory PSI specs. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).

Required Tool: Fuel Pressure Tester Kit

Clear Codes and Reset Fuel Trims

Clear DTCs and verify Long Term Fuel Trims (LTFT) return below +/- 10% on your scanner. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).

Required Tool: OBD-II Scanner

4. Ford Bronco P0171 FAQs

What causes code P0171 to trigger on a Ford Bronco?

On the Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)), P0171 is most frequently caused by Dirty or failing Mass Air Flow (MAF) sensor or Cracked intake air boot or disconnected vacuum hose. Factory sensor degradation or wiring harness wear near the engine bay are common factors.

Can I safely drive my Ford Bronco with code P0171?

Yes, but prolonged lean running increases cylinder combustion temperatures. Given that P0171 carries a Medium severity rating on Ford vehicles, we advise performing diagnostic scanning via the OBD-II port located beneath steering wheel lower shroud before extended highway driving.

Where is the diagnostic port located on the Ford Bronco?

The 16-pin OBD-II DLC connector on the Ford Bronco is situated beneath steering wheel lower shroud. It requires no special tools to plug in a standard scanner.

How much does it cost to fix P0171 on a Ford Bronco?

DIY replacement parts typically range between $80 - $350 (DIY: $15 - $70). If serviced at an authorized Ford dealership, expect an additional $120–$250 in professional labor based on their $120/hr hourly rate.