P0137 on Ford Ranger
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the Ford Ranger (2020–2026, 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP)).
1. Symptoms of P0137 on Ford Ranger
When the Engine Control Module (ECM/PCM) on your Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP)) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on Ford Ranger
Historical warranty claims and technical repair bulletins for Ford Ranger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Ford Ranger
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).
Equipment for Diagnosing Ford Ranger (P0137)
Ford Ranger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Ford Ranger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Ford Ranger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford Ranger:
4. Ford Ranger P0137 FAQs
What causes code P0137 to trigger on a Ford Ranger?
On the Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP)), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my Ford Ranger?
On the Ford Ranger, the 16-pin DLC diagnostic connector is located Lower dashboard above dead pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Ford Ranger with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.