FTC Reader Disclosure: When you purchase or register through links on our site, we may earn an affiliate commission at no extra cost to you. Read our Editorial & Advertising Policy.
P0172FordFord Ranger HubAll Ford P0172Medium Severity

P0172 on Ford Ranger: Fix & DLC Location

Factory diagnostic troubleshooting wire for fault code P0172 (System Too Rich (Bank 1) - Symptoms, Causes & Step-by-Step Fix) specifically on the Ford Ranger (2020–2026, 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP)).

2020–2026
RangerTruck
Sensor Voltage Ref
0.1V – 5.0V Ref
Ranger SAE Mode $01
ECU Network Bus
500 kbps CAN-FD
ISO 15765-4 Compliant
Drivability Status
Drivable (Short Trip)
Medium urgency level
Est. DIY Time
45 – 90 Min
Basic hand tools
Check P0172 On Another Ford Model:

1. Symptoms of P0172 on Ford Ranger

When the Engine Control Module (ECM/PCM) on your Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP)) logs fault code P0172, drivers commonly observe:

Check Engine Light on on Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP))
Strong unburnt fuel odor from exhaust on Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP))
Black carbon soot around exhaust tip on Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP))
Rough idle and engine bogging under throttle on Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP))
Noticeable drop in MPG on Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP))
Ford Ranger OBD-II Port Location
The 16-pin diagnostic connector is located Lower dashboard above dead pedal. Plug in your scan tool to verify freeze-frame sensor values.

2. Most Likely Causes on Ford Ranger

Historical warranty claims and technical repair bulletins for Ford Ranger point to the following failure distribution:

55%
Faulty or leaking fuel injector (Ford OEM Part)
25%
Contaminated Mass Air Flow (MAF) sensor (Ford OEM Part)
12%
Stuck closed EVAP canister purge valve (Ford OEM Part)
8%
Excessive fuel pressure regulator failure (Ford OEM Part)

3. Step-by-Step DIY Repair Guide for Ford Ranger

01
Clean MAF Sensor and Throttle Body

Use dedicated MAF cleaner to remove carbon buildup from sensor wires. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).

02
Check Short Term & Long Term Fuel Trims

Use live OBD-II scanner data; negative trims beyond -10% indicate the ECU is cutting fuel. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).

03
Inspect Fuel Injector Leak-Down

Perform a fuel pressure leak-down test to identify injectors leaking raw gasoline into cylinders while parked. on the Ford Ranger equipped with 2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP).

Other Common Fault Codes on Ford Ranger

Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford Ranger:

4. Ford Ranger P0172 FAQs

What causes code P0172 to trigger on a Ford Ranger?

On the Ford Ranger (2.3L EcoBoost 4-Cyl (270HP) / 2.7L V6 / 3.0L EcoBoost V6 (Raptor 405HP)), P0172 is most frequently caused by Faulty or leaking fuel injector or Contaminated Mass Air Flow (MAF) sensor.

Where is the OBD-II port located on my Ford Ranger?

On the Ford Ranger, the 16-pin DLC diagnostic connector is located Lower dashboard above dead pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.

Can I safely drive my Ford Ranger with code P0172?

Driveable short distances, but unburnt fuel can damage catalytic converters. Given that P0172 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.