P0116 on Hyundai Palisade
Factory diagnostic protocol and troubleshooting wire for fault code P0116 specifically for the Hyundai Palisade (2020–2026, 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque)).
1. Symptoms of P0116 on Hyundai Palisade
When the Engine Control Module (ECM/PCM) on your Hyundai Palisade (3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque)) logs fault code P0116, drivers commonly observe:
2. Most Likely Causes on Hyundai Palisade
Historical warranty claims and technical repair bulletins for Hyundai Palisade point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Hyundai Palisade
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0116 to note engine RPM, load, and voltage when the fault triggered. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Inspect the electrical connector and wiring harness related to P0116 for chafing, corrosion, moisture, or pin push-out. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Equipment for Diagnosing Hyundai Palisade (P0116)
VVT Oil Control Solenoid Valve
Restores accurate camshaft timing and oil pressure regulation on Hyundai Palisade.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Hyundai Palisade
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Hyundai Palisade:
4. Hyundai Palisade P0116 FAQs
What causes code P0116 to trigger on a Hyundai Palisade?
On the Hyundai Palisade (3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque)), P0116 is most frequently caused by Stuck open thermostat or Air pocket in cooling system.
Where is the OBD-II port located on my Hyundai Palisade?
On the Hyundai Palisade, the 16-pin DLC diagnostic connector is located Under driver side dashboard kick panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Hyundai Palisade with code P0116?
Caution. Verify engine is not overheating. Given that P0116 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.