P0351 on Hyundai Palisade
Factory diagnostic protocol and troubleshooting wire for fault code P0351 specifically for the Hyundai Palisade (2020–2026, 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque)).
1. Symptoms of P0351 on Hyundai Palisade
When the Engine Control Module (ECM/PCM) on your Hyundai Palisade (3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque)) logs fault code P0351, drivers commonly observe:
2. Most Likely Causes on Hyundai Palisade
Historical warranty claims and technical repair bulletins for Hyundai Palisade point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Hyundai Palisade
Identify Cylinder 1 ignition coil pack mounted on the valve cover. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Swap Coil 1 with Coil 2. Clear codes and restart engine. If code switches to P0352 (Coil B), the ignition coil is 100% defective. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Check for 12V battery power, chassis ground, and 5V trigger pulse from the PCM on the 3-pin / 4-pin harness plug. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Install a new OEM ignition coil (e.g. Denso, Motorcraft, Delphi) and replace the spark plug on Cylinder 1. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Clear DTCs and verify smooth acceleration under load. on the Hyundai Palisade equipped with 3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque).
Equipment for Diagnosing Hyundai Palisade (P0351)
Direct-Fit Laser Iridium Spark Plugs (Set of 4/6)
Pre-gapped iridium spark plugs engineered to restore smooth combustion on Hyundai Palisade.
Magnetic Swivel Spark Plug Socket Set
360-degree magnetic swivel socket prevents ceramic plug cracks inside deep engine spark wells.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Hyundai Palisade
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Hyundai Palisade:
4. Hyundai Palisade P0351 FAQs
What causes code P0351 to trigger on a Hyundai Palisade?
On the Hyundai Palisade (3.8L V6 GDI (Lambda II 291HP / 262 lb-ft torque)), P0351 is most frequently caused by Failed ignition coil pack on Cylinder 1 (Coil A) or Broken or melted wiring harness to ignition coil 1.
Where is the OBD-II port located on my Hyundai Palisade?
On the Hyundai Palisade, the 16-pin DLC diagnostic connector is located Under driver side dashboard kick panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Hyundai Palisade with code P0351?
No. Cylinder 1 ignition coil has failed completely, causing an active misfire and dumping unburned fuel into the catalytic converter. Given that P0351 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.