P0443 on Jeep Gladiator
Factory diagnostic protocol and troubleshooting wire for fault code P0443 specifically for the Jeep Gladiator (2020–2026, 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave).
1. Symptoms of P0443 on Jeep Gladiator
When the Engine Control Module (ECM/PCM) on your Jeep Gladiator (3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave) logs fault code P0443, drivers commonly observe:
2. Most Likely Causes on Jeep Gladiator
Historical warranty claims and technical repair bulletins for Jeep Gladiator point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Gladiator
Find the purge valve mounted on the intake manifold with one vacuum line leading to the intake and one to the charcoal canister. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Unplug 2-pin connector and measure resistance across terminals with multimeter. Typical spec is 14–30 ohms. If open (OL) or shorted (0 ohms), solenoid is dead. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Remove purge valve and blow into it. A healthy de-energized purge valve should be 100% sealed. If air passes through, the internal seal is stuck open. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Disconnect quick-release vapor lines, unbolt mounting bracket, snap new OEM purge valve into place, and reconnect electrical plug. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Clear DTCs with scanner and verify EVAP monitor completes. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Equipment for Diagnosing Jeep Gladiator (P0443)
OEM Tethered Fuel Gas Cap with O-Ring
Tight-sealing factory fuel cap resolves common EVAP small/large leak codes without workshop visits.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Jeep Gladiator
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Gladiator:
4. Jeep Gladiator P0443 FAQs
What causes code P0443 to trigger on a Jeep Gladiator?
On the Jeep Gladiator (3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave), P0443 is most frequently caused by Failed EVAP purge solenoid coil (open or shorted internally) or Broken or frayed wiring harness to purge valve connector.
Where is the OBD-II port located on my Jeep Gladiator?
On the Jeep Gladiator, the 16-pin DLC diagnostic connector is located Under driver dash near left knee kick panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Gladiator with code P0443?
Yes. Safe to drive, but engine may experience hard starting after refueling at gas station. Given that P0443 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.