C1288 on Jeep Grand Cherokee
Factory diagnostic protocol and troubleshooting wire for fault code C1288 specifically for the Jeep Grand Cherokee (2021–2026, 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP)).
1. Symptoms of C1288 on Jeep Grand Cherokee
When the Engine Control Module (ECM/PCM) on your Jeep Grand Cherokee (3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP)) logs fault code C1288, drivers commonly observe:
2. Most Likely Causes on Jeep Grand Cherokee
Historical warranty claims and technical repair bulletins for Jeep Grand Cherokee point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Grand Cherokee
Monitor brake pressure transducer PID. It should read near 0 bar unpressed and climb smoothly to 80+ bar when pressing pedal. on the Jeep Grand Cherokee equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP).
Unplug ABS connector and check for bent pins or brake fluid contamination. on the Jeep Grand Cherokee equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP).
Replace the ABS HCU / pump assembly or send unit to a certified rebuilder to replace the internal pressure transducer. on the Jeep Grand Cherokee equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP).
Run scan tool automated bleed procedure to purge air from ABS valves, then bleed all 4 calipers. on the Jeep Grand Cherokee equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP).
Clear DTCs and road test to verify AdvanceTrac operation. on the Jeep Grand Cherokee equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP).
Equipment for Diagnosing Jeep Grand Cherokee (C1288)
Jeep Grand Cherokee OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Jeep Grand Cherokee.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Jeep Grand Cherokee
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Grand Cherokee:
4. Jeep Grand Cherokee C1288 FAQs
What causes code C1288 to trigger on a Jeep Grand Cherokee?
On the Jeep Grand Cherokee (3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 / 4xe PHEV (375HP)), C1288 is most frequently caused by Failed internal brake pressure transducer inside the ABS Hydraulic Control Unit (HCU) or Corroded pins in ABS module electrical connector.
Where is the OBD-II port located on my Jeep Grand Cherokee?
On the Jeep Grand Cherokee, the 16-pin DLC diagnostic connector is located Under driver side dashboard above foot pedals. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Grand Cherokee with code C1288?
Caution. Normal hydraulic brakes work, but ABS, Traction Control, and AdvanceTrac are disabled. Given that C1288 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.