P0151 on Mercedes-Benz C-Class
Factory diagnostic protocol and troubleshooting wire for fault code P0151 specifically for the Mercedes-Benz C-Class (2020–2026, 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)).
1. Symptoms of P0151 on Mercedes-Benz C-Class
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz C-Class (2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)) logs fault code P0151, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz C-Class
Historical warranty claims and technical repair bulletins for Mercedes-Benz C-Class point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz C-Class
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0151 to note engine RPM, load, and voltage when the fault triggered. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Inspect the electrical connector and wiring harness related to P0151 for chafing, corrosion, moisture, or pin push-out. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Equipment for Diagnosing Mercedes-Benz C-Class (P0151)
Mercedes-Benz C-Class OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz C-Class.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz C-Class
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz C-Class:
4. Mercedes-Benz C-Class P0151 FAQs
What causes code P0151 to trigger on a Mercedes-Benz C-Class?
On the Mercedes-Benz C-Class (2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)), P0151 is most frequently caused by Failed Bank 2 upstream sensor or Bank 2 exhaust leak.
Where is the OBD-II port located on my Mercedes-Benz C-Class?
On the Mercedes-Benz C-Class, the 16-pin DLC diagnostic connector is located Under driver dash beneath purple/black sliding protective door. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz C-Class with code P0151?
Caution. Bank 2 reported lean. Given that P0151 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.