C1288 on Mercedes-Benz GLC
Factory diagnostic protocol and troubleshooting wire for fault code C1288 specifically for the Mercedes-Benz GLC (2020–2026, 2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC).
1. Symptoms of C1288 on Mercedes-Benz GLC
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLC (2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC) logs fault code C1288, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLC
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLC point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLC
Monitor brake pressure transducer PID. It should read near 0 bar unpressed and climb smoothly to 80+ bar when pressing pedal. on the Mercedes-Benz GLC equipped with 2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC.
Unplug ABS connector and check for bent pins or brake fluid contamination. on the Mercedes-Benz GLC equipped with 2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC.
Replace the ABS HCU / pump assembly or send unit to a certified rebuilder to replace the internal pressure transducer. on the Mercedes-Benz GLC equipped with 2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC.
Run scan tool automated bleed procedure to purge air from ABS valves, then bleed all 4 calipers. on the Mercedes-Benz GLC equipped with 2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC.
Clear DTCs and road test to verify AdvanceTrac operation. on the Mercedes-Benz GLC equipped with 2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC.
Equipment for Diagnosing Mercedes-Benz GLC (C1288)
Mercedes-Benz GLC OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz GLC.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz GLC
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLC:
4. Mercedes-Benz GLC C1288 FAQs
What causes code C1288 to trigger on a Mercedes-Benz GLC?
On the Mercedes-Benz GLC (2.0L Turbo 4-Cyl with EQ Boost (255HP) / AMG GLC 43 4MATIC), C1288 is most frequently caused by Failed internal brake pressure transducer inside the ABS Hydraulic Control Unit (HCU) or Corroded pins in ABS module electrical connector.
Where is the OBD-II port located on my Mercedes-Benz GLC?
On the Mercedes-Benz GLC, the 16-pin DLC diagnostic connector is located Driver lower kick panel near hood release lever. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLC with code C1288?
Caution. Normal hydraulic brakes work, but ABS, Traction Control, and AdvanceTrac are disabled. Given that C1288 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.