P0087 on Mercedes-Benz GLS
Factory diagnostic protocol and troubleshooting wire for fault code P0087 specifically for the Mercedes-Benz GLS (2020–2026, 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)).
1. Symptoms of P0087 on Mercedes-Benz GLS
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLS (3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)) logs fault code P0087, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLS
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLS point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLS
Connect an OBD-II scan tool and inspect live Mode $01 telemetry for Fuel Rail Pressure (FRP). Compare actual pressure against the ECU's desired setpoint during idle and 2,500 RPM revs. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Verify the low-pressure lift pump is delivering 55–75 PSI to the HPFP using a mechanical fuel pressure gauge on the Schrader valve. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Check the 3-wire FRP sensor harness for 5V reference, ground, and signal voltage (typically 0.5V at key-on to 4.5V at peak pressure). on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
If low-pressure feed is verified but rail pressure remains under threshold, replace the camshaft-driven HPFP and follower. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Clear DTC memory with scanner, start engine, check for fuel leaks, and drive for 15 minutes to verify fuel pressure monitors pass. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Equipment for Diagnosing Mercedes-Benz GLS (P0087)
Mercedes-Benz GLS OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz GLS.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz GLS
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLS:
4. Mercedes-Benz GLS P0087 FAQs
What causes code P0087 to trigger on a Mercedes-Benz GLS?
On the Mercedes-Benz GLS (3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)), P0087 is most frequently caused by Failing High-Pressure Fuel Pump (HPFP) or Clogged fuel filter or restricted in-tank low-pressure fuel pump (LPFP).
Where is the OBD-II port located on my Mercedes-Benz GLS?
On the Mercedes-Benz GLS, the 16-pin DLC diagnostic connector is located Driver lower knee bolster trim panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLS with code P0087?
No. Low fuel pressure causes severe engine hesitation, misfires, stalling at speed, and lean detonation. Given that P0087 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.