P0155 on Mercedes-Benz GLS
Factory diagnostic protocol and troubleshooting wire for fault code P0155 specifically for the Mercedes-Benz GLS (2020–2026, 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)).
1. Symptoms of P0155 on Mercedes-Benz GLS
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLS (3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)) logs fault code P0155, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLS
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLS point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLS
Inspect the O2 HTR fuse in the engine fuse box with a test light or multimeter. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Unplug the sensor connector and measure resistance between the two heater pins. An open circuit (infinite ohms / OL) confirms a dead internal heater. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Remove faulty sensor and install a new OEM oxygen sensor with built-in heater. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Clear DTCs and allow engine to cool down, then restart to confirm P0155 does not return. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Equipment for Diagnosing Mercedes-Benz GLS (P0155)
Mercedes-Benz GLS OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz GLS.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz GLS
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLS:
4. Mercedes-Benz GLS P0155 FAQs
What causes code P0155 to trigger on a Mercedes-Benz GLS?
On the Mercedes-Benz GLS (3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)), P0155 is most frequently caused by Burnt-out heating element inside the Bank 2 Sensor 1 O2 sensor or Blown O2 heater fuse in under-hood fuse block.
Where is the OBD-II port located on my Mercedes-Benz GLS?
On the Mercedes-Benz GLS, the 16-pin DLC diagnostic connector is located Driver lower knee bolster trim panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLS with code P0155?
Yes. The sensor will take longer to warm up, causing brief open-loop fuel delay on cold starts. Given that P0155 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.