P0116 on RAM 1500
Factory diagnostic protocol and troubleshooting wire for fault code P0116 specifically for the RAM 1500 (2020–2026, 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar).
1. Symptoms of P0116 on RAM 1500
When the Engine Control Module (ECM/PCM) on your RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar) logs fault code P0116, drivers commonly observe:
2. Most Likely Causes on RAM 1500
Historical warranty claims and technical repair bulletins for RAM 1500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 1500
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0116 to note engine RPM, load, and voltage when the fault triggered. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Inspect the electrical connector and wiring harness related to P0116 for chafing, corrosion, moisture, or pin push-out. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Equipment for Diagnosing RAM 1500 (P0116)
VVT Oil Control Solenoid Valve
Restores accurate camshaft timing and oil pressure regulation on RAM 1500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 1500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 1500:
4. RAM 1500 P0116 FAQs
What causes code P0116 to trigger on a RAM 1500?
On the RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar), P0116 is most frequently caused by Stuck open thermostat or Air pocket in cooling system.
Where is the OBD-II port located on my RAM 1500?
On the RAM 1500, the 16-pin DLC diagnostic connector is located Driver lower knee bolster panel to the right of parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 1500 with code P0116?
Caution. Verify engine is not overheating. Given that P0116 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.