U0073 on RAM 1500
Factory diagnostic protocol and troubleshooting wire for fault code U0073 specifically for the RAM 1500 (2020–2026, 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar).
1. Symptoms of U0073 on RAM 1500
When the Engine Control Module (ECM/PCM) on your RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar) logs fault code U0073, drivers commonly observe:
2. Most Likely Causes on RAM 1500
Historical warranty claims and technical repair bulletins for RAM 1500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 1500
Remove any aftermarket insurance dongles, GPS trackers, or scan tools plugged into the DLC port. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Inspect braided ground straps on engine and transmission. Clean all contact surfaces to bare metal. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Scan all modules on vehicle. Note which modules are online and which are offline to pinpoint the break in the network daisy-chain. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Verify 60 ohms across Pins 6 and 14 with battery disconnected. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Clear DTCs from all modules and road test to verify error-free network transmission. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Equipment for Diagnosing RAM 1500 (U0073)
RAM 1500 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 1500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 1500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 1500:
4. RAM 1500 U0073 FAQs
What causes code U0073 to trigger on a RAM 1500?
On the RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar), U0073 is most frequently caused by Loose or corroded ground connection on transmission or frame or Faulty Transmission Control Module (TCM) or ABS module pulling bus down.
Where is the OBD-II port located on my RAM 1500?
On the RAM 1500, the 16-pin DLC diagnostic connector is located Driver lower knee bolster panel to the right of parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 1500 with code U0073?
No. Bus is shut down due to excessive transmission errors, leaving vehicle in unpredictable limp mode. Given that U0073 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.