P0137 on RAM 2500
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the RAM 2500 (2020–2026, 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)).
1. Symptoms of P0137 on RAM 2500
When the Engine Control Module (ECM/PCM) on your RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on RAM 2500
Historical warranty claims and technical repair bulletins for RAM 2500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 2500
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Equipment for Diagnosing RAM 2500 (P0137)
RAM 2500 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 2500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 2500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 2500:
4. RAM 2500 P0137 FAQs
What causes code P0137 to trigger on a RAM 2500?
On the RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my RAM 2500?
On the RAM 2500, the 16-pin DLC diagnostic connector is located Driver footwell below steering column near parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 2500 with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.