P0443 on RAM 3500
Factory diagnostic protocol and troubleshooting wire for fault code P0443 specifically for the RAM 3500 (2020–2026, 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)).
1. Symptoms of P0443 on RAM 3500
When the Engine Control Module (ECM/PCM) on your RAM 3500 (6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)) logs fault code P0443, drivers commonly observe:
2. Most Likely Causes on RAM 3500
Historical warranty claims and technical repair bulletins for RAM 3500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 3500
Find the purge valve mounted on the intake manifold with one vacuum line leading to the intake and one to the charcoal canister. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Unplug 2-pin connector and measure resistance across terminals with multimeter. Typical spec is 14–30 ohms. If open (OL) or shorted (0 ohms), solenoid is dead. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Remove purge valve and blow into it. A healthy de-energized purge valve should be 100% sealed. If air passes through, the internal seal is stuck open. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Disconnect quick-release vapor lines, unbolt mounting bracket, snap new OEM purge valve into place, and reconnect electrical plug. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Clear DTCs with scanner and verify EVAP monitor completes. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Equipment for Diagnosing RAM 3500 (P0443)
OEM Tethered Fuel Gas Cap with O-Ring
Tight-sealing factory fuel cap resolves common EVAP small/large leak codes without workshop visits.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 3500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 3500:
4. RAM 3500 P0443 FAQs
What causes code P0443 to trigger on a RAM 3500?
On the RAM 3500 (6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)), P0443 is most frequently caused by Failed EVAP purge solenoid coil (open or shorted internally) or Broken or frayed wiring harness to purge valve connector.
Where is the OBD-II port located on my RAM 3500?
On the RAM 3500, the 16-pin DLC diagnostic connector is located Driver lower kick panel near emergency brake assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 3500 with code P0443?
Yes. Safe to drive, but engine may experience hard starting after refueling at gas station. Given that P0443 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.