P0117 on Chrysler 300
Factory diagnostic protocol and troubleshooting wire for fault code P0117 specifically for the Chrysler 300 (2020–2025, 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)).
1. Symptoms of P0117 on Chrysler 300
When the Engine Control Module (ECM/PCM) on your Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)) logs fault code P0117, drivers commonly observe:
2. Most Likely Causes on Chrysler 300
Historical warranty claims and technical repair bulletins for Chrysler 300 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler 300
Read ECT live PID on scanner. If it reads 284°F (140°C) or higher with engine cold, a short to ground exists. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Unplug sensor connector while watching live data. If temperature drops to -40°F (-40°C), the sensor itself is shorted. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
If reading stays pegged at max with sensor unplugged, inspect harness for pinch points grounding against engine block. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Allow engine to cool, unscrew old ECT sensor from coolant crossover pipe or thermostat housing, install new OEM sensor with fresh thread sealant. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Bleed air from cooling system, clear DTCs, and verify normal temperature rise on live data. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Equipment for Diagnosing Chrysler 300 (P0117)
VVT Oil Control Solenoid Valve
Restores accurate camshaft timing and oil pressure regulation on Chrysler 300.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler 300
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler 300:
4. Chrysler 300 P0117 FAQs
What causes code P0117 to trigger on a Chrysler 300?
On the Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)), P0117 is most frequently caused by ECT sensor internal short to ground or Short circuit to ground in ECT signal wiring harness.
Where is the OBD-II port located on my Chrysler 300?
On the Chrysler 300, the 16-pin DLC diagnostic connector is located Under driver side dash near left knee panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler 300 with code P0117?
No. The ECU thinks the engine is at 280°F+ (overheating) and runs rich or disables cooling fan logic. Given that P0117 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.