C1288 on Chrysler Pacifica Hybrid
Factory diagnostic protocol and troubleshooting wire for fault code C1288 specifically for the Chrysler Pacifica Hybrid (2020–2026, 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)).
1. Symptoms of C1288 on Chrysler Pacifica Hybrid
When the Engine Control Module (ECM/PCM) on your Chrysler Pacifica Hybrid (3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)) logs fault code C1288, drivers commonly observe:
2. Most Likely Causes on Chrysler Pacifica Hybrid
Historical warranty claims and technical repair bulletins for Chrysler Pacifica Hybrid point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler Pacifica Hybrid
Monitor brake pressure transducer PID. It should read near 0 bar unpressed and climb smoothly to 80+ bar when pressing pedal. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Unplug ABS connector and check for bent pins or brake fluid contamination. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Replace the ABS HCU / pump assembly or send unit to a certified rebuilder to replace the internal pressure transducer. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Run scan tool automated bleed procedure to purge air from ABS valves, then bleed all 4 calipers. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Clear DTCs and road test to verify AdvanceTrac operation. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Equipment for Diagnosing Chrysler Pacifica Hybrid (C1288)
Chrysler Pacifica Hybrid OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chrysler Pacifica Hybrid.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler Pacifica Hybrid
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler Pacifica Hybrid:
4. Chrysler Pacifica Hybrid C1288 FAQs
What causes code C1288 to trigger on a Chrysler Pacifica Hybrid?
On the Chrysler Pacifica Hybrid (3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)), C1288 is most frequently caused by Failed internal brake pressure transducer inside the ABS Hydraulic Control Unit (HCU) or Corroded pins in ABS module electrical connector.
Where is the OBD-II port located on my Chrysler Pacifica Hybrid?
On the Chrysler Pacifica Hybrid, the 16-pin DLC diagnostic connector is located Under driver side dashboard above foot pedal assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler Pacifica Hybrid with code C1288?
Caution. Normal hydraulic brakes work, but ABS, Traction Control, and AdvanceTrac are disabled. Given that C1288 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.