P0345 on Chrysler Pacifica Hybrid
Factory diagnostic protocol and troubleshooting wire for fault code P0345 specifically for the Chrysler Pacifica Hybrid (2020–2026, 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)).
1. Symptoms of P0345 on Chrysler Pacifica Hybrid
When the Engine Control Module (ECM/PCM) on your Chrysler Pacifica Hybrid (3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)) logs fault code P0345, drivers commonly observe:
2. Most Likely Causes on Chrysler Pacifica Hybrid
Historical warranty claims and technical repair bulletins for Chrysler Pacifica Hybrid point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler Pacifica Hybrid
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0345 to note engine RPM, load, and voltage when the fault triggered. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Inspect the electrical connector and wiring harness related to P0345 for chafing, corrosion, moisture, or pin push-out. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Chrysler Pacifica Hybrid equipped with 3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV).
Equipment for Diagnosing Chrysler Pacifica Hybrid (P0345)
Chrysler Pacifica Hybrid OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chrysler Pacifica Hybrid.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler Pacifica Hybrid
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler Pacifica Hybrid:
4. Chrysler Pacifica Hybrid P0345 FAQs
What causes code P0345 to trigger on a Chrysler Pacifica Hybrid?
On the Chrysler Pacifica Hybrid (3.6L Atkinson-Cycle V6 + Dual Electric Motors (260 HP PHEV / 32-Mile EV)), P0345 is most frequently caused by Defective Bank 2 camshaft position sensor or Broken wiring harness.
Where is the OBD-II port located on my Chrysler Pacifica Hybrid?
On the Chrysler Pacifica Hybrid, the 16-pin DLC diagnostic connector is located Under driver side dashboard above foot pedal assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler Pacifica Hybrid with code P0345?
Caution. Bank 2 cam signal missing. Given that P0345 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.