P0137 on Jeep Wrangler
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the Jeep Wrangler (2020–2026, 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP)).
1. Symptoms of P0137 on Jeep Wrangler
When the Engine Control Module (ECM/PCM) on your Jeep Wrangler (3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP)) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on Jeep Wrangler
Historical warranty claims and technical repair bulletins for Jeep Wrangler point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Wrangler
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Equipment for Diagnosing Jeep Wrangler (P0137)
Jeep Wrangler OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Jeep Wrangler.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Jeep Wrangler
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Wrangler:
4. Jeep Wrangler P0137 FAQs
What causes code P0137 to trigger on a Jeep Wrangler?
On the Jeep Wrangler (3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP)), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my Jeep Wrangler?
On the Jeep Wrangler, the 16-pin DLC diagnostic connector is located Below steering wheel near driver left knee. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Wrangler with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.