U0073 on Mercedes-Benz E-Class
Factory diagnostic protocol and troubleshooting wire for fault code U0073 specifically for the Mercedes-Benz E-Class (2020–2026, 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP)).
1. Symptoms of U0073 on Mercedes-Benz E-Class
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz E-Class (2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP)) logs fault code U0073, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz E-Class
Historical warranty claims and technical repair bulletins for Mercedes-Benz E-Class point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz E-Class
Remove any aftermarket insurance dongles, GPS trackers, or scan tools plugged into the DLC port. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Inspect braided ground straps on engine and transmission. Clean all contact surfaces to bare metal. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Scan all modules on vehicle. Note which modules are online and which are offline to pinpoint the break in the network daisy-chain. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Verify 60 ohms across Pins 6 and 14 with battery disconnected. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Clear DTCs from all modules and road test to verify error-free network transmission. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Equipment for Diagnosing Mercedes-Benz E-Class (U0073)
Mercedes-Benz E-Class OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz E-Class.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz E-Class
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz E-Class:
4. Mercedes-Benz E-Class U0073 FAQs
What causes code U0073 to trigger on a Mercedes-Benz E-Class?
On the Mercedes-Benz E-Class (2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP)), U0073 is most frequently caused by Loose or corroded ground connection on transmission or frame or Faulty Transmission Control Module (TCM) or ABS module pulling bus down.
Where is the OBD-II port located on my Mercedes-Benz E-Class?
On the Mercedes-Benz E-Class, the 16-pin DLC diagnostic connector is located Under driver dashboard behind safety clip bezel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz E-Class with code U0073?
No. Bus is shut down due to excessive transmission errors, leaving vehicle in unpredictable limp mode. Given that U0073 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.