U0073 on Mercedes-Benz GLE
Factory diagnostic protocol and troubleshooting wire for fault code U0073 specifically for the Mercedes-Benz GLE (2020–2026, 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580).
1. Symptoms of U0073 on Mercedes-Benz GLE
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580) logs fault code U0073, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLE
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLE point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLE
Remove any aftermarket insurance dongles, GPS trackers, or scan tools plugged into the DLC port. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Inspect braided ground straps on engine and transmission. Clean all contact surfaces to bare metal. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Scan all modules on vehicle. Note which modules are online and which are offline to pinpoint the break in the network daisy-chain. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Verify 60 ohms across Pins 6 and 14 with battery disconnected. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Clear DTCs from all modules and road test to verify error-free network transmission. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Equipment for Diagnosing Mercedes-Benz GLE (U0073)
Mercedes-Benz GLE OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz GLE.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz GLE
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLE:
4. Mercedes-Benz GLE U0073 FAQs
What causes code U0073 to trigger on a Mercedes-Benz GLE?
On the Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580), U0073 is most frequently caused by Loose or corroded ground connection on transmission or frame or Faulty Transmission Control Module (TCM) or ABS module pulling bus down.
Where is the OBD-II port located on my Mercedes-Benz GLE?
On the Mercedes-Benz GLE, the 16-pin DLC diagnostic connector is located Driver footwell directly above parking brake pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLE with code U0073?
No. Bus is shut down due to excessive transmission errors, leaving vehicle in unpredictable limp mode. Given that U0073 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.