P0201 on Mercedes-Benz GLE
Factory diagnostic protocol and troubleshooting wire for fault code P0201 specifically for the Mercedes-Benz GLE (2020–2026, 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580).
1. Symptoms of P0201 on Mercedes-Benz GLE
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580) logs fault code P0201, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLE
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLE point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLE
Locate Cylinder 1 fuel injector. Ensure connector is securely clicked in and wires are not frayed. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Unplug connector and measure resistance across the two injector pins. Normal is 11–16 ohms for high-impedance injectors. If open (OL) or shorted (0 ohms), replace injector. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Plug a noid light into the harness connector and crank engine. Rapid flashing confirms PCM driver is pulsing the circuit. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Relieve fuel rail pressure, unbolt fuel rail mounting bolts, gently pull rail up, remove retaining clip, and replace Cylinder 1 injector with new OEM unit with lubricated O-rings. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Turn key to ON to prime fuel system, check for fuel rail leaks, start engine, clear DTCs, and verify smooth idle. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Equipment for Diagnosing Mercedes-Benz GLE (P0201)
Mercedes-Benz GLE OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz GLE.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz GLE
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLE:
4. Mercedes-Benz GLE P0201 FAQs
What causes code P0201 to trigger on a Mercedes-Benz GLE?
On the Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580), P0201 is most frequently caused by Failed, open, or shorted fuel injector solenoid on Cylinder 1 or Damaged or chewed wiring harness to Cylinder 1 injector.
Where is the OBD-II port located on my Mercedes-Benz GLE?
On the Mercedes-Benz GLE, the 16-pin DLC diagnostic connector is located Driver footwell directly above parking brake pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLE with code P0201?
No. Dead injector on Cylinder 1 causes immediate dead misfire, severe shaking, and unburned air/fuel delivery imbalance. Given that P0201 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.