P0705 on Mercedes-Benz GLE
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the Mercedes-Benz GLE (2020–2026, 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580).
1. Symptoms of P0705 on Mercedes-Benz GLE
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLE
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLE point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLE
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Equipment for Diagnosing Mercedes-Benz GLE (P0705)
Mercedes-Benz GLE OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Mercedes-Benz GLE.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Mercedes-Benz GLE
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLE:
4. Mercedes-Benz GLE P0705 FAQs
What causes code P0705 to trigger on a Mercedes-Benz GLE?
On the Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my Mercedes-Benz GLE?
On the Mercedes-Benz GLE, the 16-pin DLC diagnostic connector is located Driver footwell directly above parking brake pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLE with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.