P0705 on RAM 1500 TRX
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the RAM 1500 TRX (2021–2024, 6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2)).
1. Symptoms of P0705 on RAM 1500 TRX
When the Engine Control Module (ECM/PCM) on your RAM 1500 TRX (6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2)) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on RAM 1500 TRX
Historical warranty claims and technical repair bulletins for RAM 1500 TRX point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 1500 TRX
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the RAM 1500 TRX equipped with 6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2).
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the RAM 1500 TRX equipped with 6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2).
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the RAM 1500 TRX equipped with 6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2).
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the RAM 1500 TRX equipped with 6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2).
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the RAM 1500 TRX equipped with 6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2).
Equipment for Diagnosing RAM 1500 TRX (P0705)
RAM 1500 TRX OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 1500 TRX.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 1500 TRX
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 1500 TRX:
4. RAM 1500 TRX P0705 FAQs
What causes code P0705 to trigger on a RAM 1500 TRX?
On the RAM 1500 TRX (6.2L Supercharged HEMI V8 (702HP / 650 lb-ft / Bilstein Black Hawk e2)), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my RAM 1500 TRX?
On the RAM 1500 TRX, the 16-pin DLC diagnostic connector is located Driver lower dash assembly next to hood release lever. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 1500 TRX with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.