FTC Reader Disclosure: When you purchase or register through links on our site, we may earn an affiliate commission at no extra cost to you. Read our Editorial & Advertising Policy.

P0442 on Toyota Tundra: Fix & DLC Location

Factory diagnostic troubleshooting wire for fault code P0442 (EVAP System Small Leak Detected - Diagnosis & Repair Guide) specifically on the Toyota Tundra (2022–2026, 3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP)).

2022–2026
TundraTruck
Sensor Voltage Ref
0.1V – 5.0V Ref
Tundra SAE Mode $01
ECU Network Bus
500 kbps CAN-FD
ISO 15765-4 Compliant
Drivability Status
Drivable (Short Trip)
Low urgency level
Est. DIY Time
45 – 90 Min
Basic hand tools
Check P0442 On Another Toyota Model:

1. Symptoms of P0442 on Toyota Tundra

When the Engine Control Module (ECM/PCM) on your Toyota Tundra (3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP)) logs fault code P0442, drivers commonly observe:

Check Engine Light on on Toyota Tundra (3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP))
Intermittent faint fuel odor near rear wheel well on Toyota Tundra (3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP))
Failed OBD-II smog check on Toyota Tundra (3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP))
Toyota Tundra OBD-II Port Location
The 16-pin diagnostic connector is located Driver side lower dash assembly near parking brake. Plug in your scan tool to verify freeze-frame sensor values.

2. Most Likely Causes on Toyota Tundra

Historical warranty claims and technical repair bulletins for Toyota Tundra point to the following failure distribution:

55%
Worn or cracked gas cap rubber seal (Toyota OEM Part)
25%
Small split in charcoal canister vapor line (Toyota OEM Part)
12%
Leaking EVAP vent valve solenoid (Toyota OEM Part)

3. Step-by-Step DIY Repair Guide for Toyota Tundra

01
Clean or Replace Gas Cap O-Ring

Inspect the gas cap gasket for micro-cracks or debris. Replace with OEM cap if hardened. on the Toyota Tundra equipped with 3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP).

02
Perform EVAP Smoke Machine Test

Inject mineral oil smoke into the EVAP service port to visually pinpoint the pinhole leak. on the Toyota Tundra equipped with 3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP).

03
Replace Vent Solenoid Valve

If smoke escapes from the canister vent, replace the stuck solenoid. on the Toyota Tundra equipped with 3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP).

Other Common Fault Codes on Toyota Tundra

Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Toyota Tundra:

4. Toyota Tundra P0442 FAQs

What causes code P0442 to trigger on a Toyota Tundra?

On the Toyota Tundra (3.4L Twin-Turbo V6 (V35A-FTS 389HP) / i-FORCE MAX Hybrid (437HP)), P0442 is most frequently caused by Worn or cracked gas cap rubber seal or Small split in charcoal canister vapor line.

Where is the OBD-II port located on my Toyota Tundra?

On the Toyota Tundra, the 16-pin DLC diagnostic connector is located Driver side lower dash assembly near parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.

Can I safely drive my Toyota Tundra with code P0442?

Safe to drive. Will not damage engine internals. Given that P0442 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.