P0150 on Dodge Charger
Factory diagnostic protocol and troubleshooting wire for fault code P0150 specifically for the Dodge Charger (2020–2026, 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo).
1. Symptoms of P0150 on Dodge Charger
When the Engine Control Module (ECM/PCM) on your Dodge Charger (5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo) logs fault code P0150, drivers commonly observe:
2. Most Likely Causes on Dodge Charger
Historical warranty claims and technical repair bulletins for Dodge Charger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Charger
Identify Bank 2 (the cylinder bank that does NOT contain Cylinder 1). Locate the upstream O2 sensor before the catalytic converter. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Check the 4-wire or 5-wire harness for damage. Measure heater resistance across pins (typically 4–15 ohms). on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Use an O2 sensor socket to remove the old sensor, thread in new OEM replacement, and torque securely. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Clear DTCs and monitor Bank 2 Short Term Fuel Trim (STFT) to verify fuel control restoration. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Equipment for Diagnosing Dodge Charger (P0150)
Dodge Charger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Charger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Charger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Charger:
4. Dodge Charger P0150 FAQs
What causes code P0150 to trigger on a Dodge Charger?
On the Dodge Charger (5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo), P0150 is most frequently caused by Failing Bank 2 upstream oxygen sensor or Damaged wiring or melted harness on Bank 2 exhaust manifold.
Where is the OBD-II port located on my Dodge Charger?
On the Dodge Charger, the 16-pin DLC diagnostic connector is located Driver lower dash assembly next to hood lever. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Charger with code P0150?
Yes, for limited driving. Bank 2 cylinders will operate in open-loop fail-safe mode. Given that P0150 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.