U0142 on Ford Bronco
Factory diagnostic protocol and troubleshooting wire for fault code U0142 specifically for the Ford Bronco (2021–2026, 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)).
1. Symptoms of U0142 on Ford Bronco
When the Engine Control Module (ECM/PCM) on your Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)) logs fault code U0142, drivers commonly observe:
2. Most Likely Causes on Ford Bronco
Historical warranty claims and technical repair bulletins for Ford Bronco point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Ford Bronco
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code U0142 to note engine RPM, load, and voltage when the fault triggered. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Inspect the electrical connector and wiring harness related to U0142 for chafing, corrosion, moisture, or pin push-out. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Equipment for Diagnosing Ford Bronco (U0142)
Ford Bronco OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Ford Bronco.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Ford Bronco
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford Bronco:
4. Ford Bronco U0142 FAQs
What causes code U0142 to trigger on a Ford Bronco?
On the Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)), U0142 is most frequently caused by CAN bus communication break or Blown BCM fuse.
Where is the OBD-II port located on my Ford Bronco?
On the Ford Bronco, the 16-pin DLC diagnostic connector is located Beneath steering wheel lower shroud. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Ford Bronco with code U0142?
Yes. Secondary body electronics offline. Given that U0142 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.