U0073 on Dodge Charger
Factory diagnostic protocol and troubleshooting wire for fault code U0073 specifically for the Dodge Charger (2020–2026, 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo).
1. Symptoms of U0073 on Dodge Charger
When the Engine Control Module (ECM/PCM) on your Dodge Charger (5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo) logs fault code U0073, drivers commonly observe:
2. Most Likely Causes on Dodge Charger
Historical warranty claims and technical repair bulletins for Dodge Charger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Charger
Remove any aftermarket insurance dongles, GPS trackers, or scan tools plugged into the DLC port. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Inspect braided ground straps on engine and transmission. Clean all contact surfaces to bare metal. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Scan all modules on vehicle. Note which modules are online and which are offline to pinpoint the break in the network daisy-chain. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Verify 60 ohms across Pins 6 and 14 with battery disconnected. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Clear DTCs from all modules and road test to verify error-free network transmission. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Equipment for Diagnosing Dodge Charger (U0073)
Dodge Charger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Charger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Charger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Charger:
4. Dodge Charger U0073 FAQs
What causes code U0073 to trigger on a Dodge Charger?
On the Dodge Charger (5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo), U0073 is most frequently caused by Loose or corroded ground connection on transmission or frame or Faulty Transmission Control Module (TCM) or ABS module pulling bus down.
Where is the OBD-II port located on my Dodge Charger?
On the Dodge Charger, the 16-pin DLC diagnostic connector is located Driver lower dash assembly next to hood lever. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Charger with code U0073?
No. Bus is shut down due to excessive transmission errors, leaving vehicle in unpredictable limp mode. Given that U0073 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.